¡¡
¡¡
¡¡ Strong Ceramic Tile Back Glue

Product introduction

The America DuLaBo  ceramic tile back glue is the production of using the imported high quality polymer emulsion with high performance additives refining. This production is the new environmentally friendly production with high bonding strength and high permeability, especially for wet gluing of various ceramic tiles and marbles, which effectively improves the bond strength between ceramic tiles and marbles,  and the bonding materials. Therefore, our production solves a series of problems ,such as  hollowing, shedding efforescence seepage pollution and so on, which are common in ceramic tiles and marbles during the process of wet gluing.

Product features

Quick brushing and quick sticking ; convenient construction ;low cost; time saving and labor saving;

With strong permeability and adhesion; this production's bond strength is high, which could quickly penetrate into the cement, ceramic tile or stone, and then solidify into a solid bonding layer . As a result ,the bonding layer forms  a new rough surface with high viscosity, which enhances the bolding ability with bonding materials, and effectively prevent the hollowing and falling tiles and marble.

Mildew resistant, acid and alkali resistant, excellent anticorrosion performance; Have certain waterproof performance, enhance waterproof efforts and seepage prevention; be durable

Aging , high temperature ,and  freeze-thaw resistance,; Strong compatibility with cement based adhesive materials ; strong adhesion;

Good flexibility, hardening shrinkage small, strong anti-crack extension ability, Reduce tile cracks;

Non-toxic, odorless, no harmful substances, green environmental protection.

Adaptive range

It's widely used in gluing of the renovation of the old wall, tiles, polished tiles, Vitrified bricks, glass mosaic, marble, culture stone, granite, sandstone, artificial stone and other materials ;  aerated concrete bricks ,  anhydrite and other surface modification of the high water absorbing; other dense texture, low water absorption, smooth surface of the back  brick interface's  treatment,  and they can effectively prevent or delay the occurrence of stone lesions.

Also can be used in smooth surface reconstruction after the demolition of the concrete frame template, and repairing and plastering of newly constructed concrete.

Also applies to the old tile surface directly refurbishing, and treated tile surface can be pasted tiles again without knocking bricks

construction method:

Construction conditions: construction environment shall be dry;  the relative humidity should be less than 70%; good ventilation; base and environmental temperature should not be lower than  5¡ãC£»

Surface cleaning: firstly check the back veneer that is  smooth and  clean or not, and before brushing the back of tiles we need to clean up them with the wet towels , as well as remove the dust, oil, wax, protective agent, mold discharging and other things  that affects the bond at the back of tiles.

After mixing evenly, you can use  brush or roller evenly blush the back of decorative brick material with gum, and interface must be painted over, not leak brush;

After blushing, it should get 5-minute sun-cure until  the emulsion surface dry. Or after brushing directly with cement paste wet paste, which means quick brushing and quick sticking , and you don't have to wait.

Using 1 bag of cement with about 1/2 of fine sand (suggests adding some America DuLaBo ceramic tiles fine glue) , and mixing the water into the mortar. And then scrape the grouting mortar to the back of blushed ceramic tiles, and make the tiles on the wall with a rubber hammer tapping for leveling. When the tiles couldn't move any more, just clean them up.

During construction and completion within 24 hours, the base surface and environmental temperature should be between 5~35 degree,  and the just  completed construction of  materials should avoid drenching water within 24 hours.

Attention

Before using you should read the instructions; This product shall not be diluted with water or  added any other agent; Ban construction on rainy days

When you blushing, you should pay attention to avoid the adhesion agent flowing to the front, and that would be very difficult to clean. Blushed tiles' back should put upward, and shouldn't make them stand or vertical put.

After the construction, you should do well the maintenance and protection work in order to prevent pollution, collision and destroying. Brushing tools should be cleaned as soon as possible with water.

During construction ,you should wear a mask. If you accidentally have eye contact , you should take timely medical treatment.

This product should be stored in a cool and dry environment, and avoid moisture and rain.

Any base surface before the large area of construction, you must do the advanced test on a small area. Any risk could be seen in the small test and be failed to avoid, we do not assume any responsibility.

Brushing amount: about 10 -12square meters per kilogram brushing

Product packaging: 5kg/ barrel

Shelf life: 6 degrees  to 35 degrees, storage period of 12 months

¡¡ | Concrete sealing hardener | Ground solidify | Metope cure adhesive | No odor-flexible waterproof mortar | Tile adhesive fine | No odor-flexible waterproof paint | No odor-flexible waterproof mortar | Infiltration crystalline waterproof | Cracks glue
¡¡ Company specializing in the development and production of chemical glue.
¡¡ ¡¡
¡¡ CopyRight£ºAMERICAN DURABLE CHEMICAL PAINT INC    Tel£º021-57735372    Óʾֵǽ Technical Support£ºpr-design.cn